- Read Time: 5 mins
- Hits: 84558
One of the elements that makes woodworking projects stand out is the attention to detail that the woodworker builds into their works. In some cases, one of the details that help to define a piece and break up large areas of plain wood ... is something called Fluting. A commonplace that you might find fluting would be a surround of a fireplace. Often there are wide pieces of wood around a fireplace and one way of making these plain pieces of wood more attractive is to "flute" them. You will also find fluting on table legs, bookcases, large wooden beds and other things that use wide boards in the construction.
Watch it on Youtube: https://www.youtube.com/embed/yacSIDmSeYM
My goal with this jig project was to make a jig that I could use on many different projects that I could rely on as being accurate and for making repeatable flutes when I need them ...
>>>> Link to Woodworkweb Amazon Affiliate Store - https://www.amazon.com/shop/woodworkweb <<<<
- Read Time: 5 mins
- Hits: 56353
The goal for this jig was to build a jig that was portable and accurate in making crosscuts with a circular saw, and at the same time, if it could prevent or somehow collect dust, that would be nice as well. All three were accomplished but the dust collection remains tenuous as a value, but I did reduce the volumes somewhat. What I really liked is just how portable and useful this jig is, it worked better than I expected, giving extremely accurate cuts, it's light to carry around and for anyone who is looking for very nice crosscut mechanism for their circular saw, this could be the one to try. Circular saws are not universal in their designs, so a jig or sled like this could well be different for different saws, the dimensions I am giving are only guidelines.
*** UPDATE *** Many thanks to Larry Chrisman for providing both a SketchUp file and PDF file found at the highlighted links, or by going to Plans on this site.
Watch it on Youtube: https://www.youtube.com/embed/zzYTTEaYm-w
I made mine from scrap woods I had around the workshop and even then, it didn't take much of that. I didn't have any plans to start with except the size of the circular saw blade and the dimensions of the saw it'self, and with that, I started and here is my methodology.
>>>> Link to Woodworkweb Amazon Affiliate Store - https://www.amazon.com/shop/woodworkweb <<<<
- Read Time: 5 mins
- Hits: 16244
One of the reasons there are so many different woodworking jigs is that one jig that does a specific job, may not necessarily perform a similar job when needed, or it may be too cumbersome to use. Such is the case with this Table Saw Mitre Gauge attached Tapering Jig or Wedge Making jig as some call it. This jig is not well suited for making things like tapered legs where there are tapers on all 4 sides. This is because when you taper 2 opposing sides, the last 2 sides need support in order for them to make equal angle cuts, and you also need to compensate for the width of the saw blade with something like veneers. It can be done, but this jig is very cumbersome for that kind of cut. This jig I made in a previous video is far better for making tapered legs and for trimming uneven edged wood, you can check it out here.
Watch it on Youtube: https://www.youtube.com/embed/jzc5uil5_-s
This tapering jig is far more suited for smaller, one or maybe 2 sided cuts. I like it because it is variable in many ways including the thickness of stock, width of stock and quite wide variable angles of wedge or tapered sizes. I made mine replicating a 30 - 60 degree triangle, only because it gave me different lengths of the triangle to work with ...
>>>> Link to Woodworkweb Amazon Affiliate Store - https://www.amazon.com/shop/woodworkweb <<<<
- Read Time: 3 mins
- Hits: 72763
It seems I am forever needing to cut a board into equal halves. I always have a tape measure handy, but sometimes it's just quicker and more accurate to use a center finding jig to find the center of a board, especially when they are strange widths ... like 13-9/16. Oh sure I can stop and figure this out in my head ... of use the metric scale, or just grab my center finder jig and have it done in a few seconds ... and anyway, it's fun to make these jigs and see if there are ways we can make them better and more useful.
Watch it on Youtube: https://youtu.be/54IMIBnKEnw
This version of the center finding jig has been around for many, many years but I have never seen an adjustable version ... not that there aren't some out there somewhere, just that I have never seen one.