- Read Time: 7 mins
- Hits: 10563
Book,
Magazines, Newspaper clippings, photocopies of wood working projects and pictures. That pretty much describes my woodworking library. Now let me describe where I keep it, in the book case in living room or next to my favorite chair, some in the bedside table, a few others in the workshop, and of course at least a couple of magazines in that place where we all go for a bit of quite time every day.
When it comes time to try and find something that I have bookmarked or need reference to, just finding the magazine, book or photo copy can be a challenge, so I decided it was high time to build a small Library Cupboard for the workshop so I can find things, when I need them. The first thing I did was stack up all by library items in one place to see how much space they take up, then allow for a bit of extra room that will surely be needed in the future.
Since this cabinet is going to be holding a fair bit of weight, I decided that instead of the standard rabbets, I would make the corners of this cabinet as box joints. That way The carcass will be strong enough to hold the books and can still be wall mounted and have doors attached to keep the dust out.
Click "MORE" ... to watch 2 more videos on this topic ...
- Read Time: 5 mins
- Hits: 15013
There aren't many woodworking projects that are nice looking and useful that you can make in one day, but this is one of those exceptions. This little umbrella stand is easy to make and even finish in one day, provided you are using a pocket hole system, and in our case we used the Kreg unit. Of course the advantage of holding joints together with pocket screws is that you don't have to wait for glue to dry, which speeds things up immensely. We love the Kreg Pocket Hole System for other reasons too, there is no glue oozing our of joints, so you don't have to worry about white spots that the finish didn't penetrate because there was left over glue on the wood, and for some projects that need to be taken apart later on, the pocket hole screws are perfect, and they really do hold very well.
To start off with we needed 4 corner posts and after fitting together some scraps and knowing that our middle cross gable pieces were going to be 3/4 inch, we finally decided that the corner posts would need to be 1-1/4 inches square and 26 inches long. See CUT LIST in the Read More Section. When ever possible, always cut the largest pieces of your project first because what is left over can often be used of other pieces in the project, and in our case we were able to get about half or more of the spindles that were needed, these were the half inch square by 17 inch long pieces in the middle of each side.
The next pieces we need to make were the upper and lower gables. We decided on 3-1/2 inch by 3/4 inch Garry Oak. The first thing we needed to do with these pieces was to run a 1/2 inch by 1/2 inch dado in one end to hold the spindles. We set up the table saw as close to the center of the edge of the board as we could, and ran the board through.
- Read Time: 4 mins
- Hits: 14334
If you are one of the millions of people who watch programs like The Antiques Road Show, American Pickers, Canadian Pickers, Pawn Stars and other similar shows, or if you have ever been to an antique or collectibles show and sale, you have seen these little display boxes at various sellers tables. You may have even seen them in someone's home or business to display small, featured and valued items. They are called all sorts of things, slanted display boxes, pickers display boxes, collectible boxes and sellers show boxes and so on.
In this video we make our version of this box with a bit of a twist, our box will use box joints for the corners to make it more attractive and sturdier and instead of painting the inside or lining the bottom with felt, we are going to flock the whole inside of the box, a rich green to make items in the box stand out. This project will consist of 3 parts, making the box, making the top or lid and finally, finishing and flocking the box.
Part 1 - Making the Box
Part 2 - Making the Top or Lid for the Box
Click below, for more details on sizes and other construction detail.
- Read Time: 2 mins
- Hits: 10229
There is something rewarding about taking rough lumber and turning it into fine furniture, especially if it is a design you love to make. Such is the case with this little side table, in the Arts and Crafts (A&C) style of furniture. I thought about all the furniture that I love to make and discovered that there are a number of types and styles, starting with the A&C style of furniture. I am a big fan of William Morris, designer of course of the Morris Chair, Gustav Stickely, Harvey Ellis, Greene and Greene and others, but I am also a big fan of Thomas Molesworth who made a very unique type of furniture in the mid-west. All of these people contributed greatly to styles and types of furniture we have today, and they influenced generations of woodworkers.
This little side table is a simple design, and like most woodworkers, I have adapted some of my own wrinkles to, by combining, in a way, the styles of Havery Ellis and Thomas Molesworth. The carcass of the table is recognisable as a typical A&C table, but the top boasts a natural edge rather than a sawn, planed and finished edge. I also like the height and size of the table, all of which was designed using a Fibonacci Gauge in order to get pleasing lines and dimensions.
But there is a lot more than simply building a piece of furniture. It needs to be finished AND with this piece ti has a natural edge top, so what do we do for edge treatment for the top ... click below to see the following videos ...