Selecting Saw Blades for Table Saws
- Read Time: 9 mins
- Hits: 9519
There are hundreds of different table saw blades available from many, many different manufacturers so how do you begin by selecting the one you need. There are probably a number of blades that will work for you so narrowing down what works best for the amount of money you want to spend is a simple matter of knowing the basiscs. This article along with the video will help eveyone new to woodworking, gain the knowledge to make wiser choices when selecting table saw blades.
There are 3 questions you want to ask yourself when looking for table saw blades, 1) - What material will you be cuting 2) - What machine do you have (table saw, mitre saw and what size, 9 inch, 10 inch, 12 inch and is horse power or amperage of the saw) and finally 3) - what is the purpose of what you are doing - furniture making, building a fence or a chicken coup or installing crown molding. 3 very relevant questions that will all come together to help you find the best blade(s) for your use.
Watch this and other similar videos on YouTube - https://youtu.be/qUHxMsL-e6o
Easily the most popular table saw blades on the market right now are 10 inch blades and also the widest selection. There are basically 2 types of blades, Full Kerf - approx 1/8" (kerf referrs to the width of the saw blade tooth) and Thin Kerf - approx 3/32".
Full kerf blades are thicker teeth, thicker steel bodies and heavier blades. They are used in bigger more powerful saws. Full kerf blades have more carbide in their teeth which means the teeth stay sharper longer, and they can be resharpened more more times than thin kerf. Full kerf blades will cut a wider swath so they will use up more material and will create slightly more saw dust and shavings. Full kerf will be slightly harder to push material through as the width of the blades is slightly wider. Full kerf blades are often preferred by commercial and industrial businesses that are using saw blades constantly as these blades withstand harder more rugged use and can be resharpened more often.
Table Saw Mitre Jig: Make Easy Mitres Cuts & Spline Joints Every Time!
- Read Time: 5 mins
- Hits: 18014
For most woodworkers, the table saw is most used machine in the shop so it stands to reason that among the most popular and useful jigs are for the table saw. One of the nice features of most table saws is the ability of the saw to angle the blade, often up to 45 degrees, for special angled cuts. The problem with many table saws, especially saws that are older is the mechanism that allows the blade to be angled is often hard to move, and at best, you still need to get down on your hands and knees and crank the blade over ... make a cut or two, then crank the blade vertical again and make sure it is absolutely square to the table saw's deck. Not difficult, but tedious and time consuming and often for only one or two cuts ... and hopefully they are perfect, because who wants to repeat this process?
Watch this and other similar videos on YouTube: https://youtu.be/p5MQrAKLqNw
In this video I am finally getting around to making a jig that can be popped on top the table saw, trapped by the fence so it is safe and adjustable to use and quick and easy to make angled cuts without having to fuss around with moving the blade ... and here are the dimensions ...
Reciprocating Saws and Blades - Beginner #29
- Read Time: 7 mins
- Hits: 6770
Reciprocating saws or "recip saws" as they are commonly called, are not commonly regarded as woodworking tools but many woodworkers have and use them. Recip Saws are standard fare for home reno and DIY projects because they can be used to quickly remove parts of buildings, and with the correct blades, can easily cut through wood and nails so they are big time savers. The good thing with recip saws is that they all take standard blades. The blades can be inserted right side up, or upside down on most saws. Once the collar or collet as some call it, is twisted and the blade inserted they are locked in place. To remove the blades, twisting the collar will release the blade.
The one thing I have learned is that when it comes to recip saws, bigger is better. By that I mean that in many cases, the underpowered recip saws are just not capable of doing the work that many people expect from them. Whether you are looking at a corded or cordless tool, my recommendation is to purchase the most powerful one you can. I seldom give this kind of advice but for recip saws, I have never, ever heard anyone complain that the purchased a saw that was too powerful ... I have heard them complain that they should have purchased a more powerful tool.
Watch this and other similar videos on YouTube - https://youtu.be/gWajERepEdE
Like many tools that cut, the blades you select for the saw can make an enormous on how easily you can get the job done, and recip blades are no exception ....
Make a Picture Frame Corner Rabbeting Jig for the Table Saw
- Read Time: 5 mins
- Hits: 8740
Making picture frames is a popular woodworking project but it's not alway easy to decide how to fasten the corners that are often edge grain wood that often doesn't readily take many woodworking glues to secure it. Mechanical fasteners are popular like screws, nails and staples and sometimes splines are cut into the corners then wood veneer is glued into the splinces to make a very strong corner, and decorative as seen from the edge, which picture frames are seldom viewed from. Using rabbets is less common, but is equally as strong as splines, and they add a different look to the picture frame. Cuting rabbets into corners is not limited to picture frames, it could also be used in doors and door frames and other edging and surround applications. Sometime dowels can also be added to the rabbets, but this can also look "over done" in terms of looks of the frame or door.
Watch this and other similar videos on YouTube - https://youtu.be/0SmyNi804ec
The version shown in the video is a common design, simple to make and works well. The minimum dimensions ...
Making Production Jigs and Machine Stops to Create LED Lanterns
- Read Time: 3 mins
- Hits: 6326
From time to time we find ourselves in situations where we need to make a kind of production run .. that is, we need to make a number of identical pieces that are composed of identical parts, much the same as a small factory. To accomplish this we often have jigs that make duplication quick, easy and accurate, and we can also set up our machinery with what are called "stops" so that cutting wood on things like table saws or chop saws can be done repetitively with accurate results. In this video, that is exactly what I am doing, a small production run of a lantern that will be assembled and set up in another video, attached to this article.
These videos were created to make some small wooden lanterns that were designed to help commemorate Canada's 150th Birthday for July 1, 2017. Some of the articles shown in the video were kindly sent to us from the nice folks at Canadian Tire, like the #redandwhite LED lights, the Canadian Flag and the commemorative T-shirt to help us all celebrate and regonize this time ... Happy Birthday Canada !!
Watch this and other similar videos on YouTube - https://youtu.be/nzvZnv6WwrA
To start off with, we need wood to work with so using machine stops to get idential pieces of wood is a great start.Once we have some identical pieces of wood, we can start making and using jigs to get repiicated cuts that can be assebled in kind of productin line system.
The video is self explanitory but make sure you check in next time to see how this all comes together ...
Assembly and Set-Up ...
Once all the parts are made, the next step is putting them together, finishing them and setting them up.
Watch this and other similar videos on YouTube - https://youtu.be/xX36FlErKCc
This was a fun project and it's always nice when you can come away from builds like this with a nice, funtional item that others can see and appreciate.
How to Make a Mortising Jig for the Router
- Read Time: 6 mins
- Hits: 25930
Mortise and Tenon wood joinery is one of the most common ways of making woodworking jonts in quality furniture, timber framing and other forms of woodworking. In this video I am completing the other half of the jig making exercise by making a mortising jig. The mortise is this hole in which the tenon is inserted, and often glued or pinned, that go together to make the woodworking joint. There are many, many ways of making mortises from dedicated mortising machines, to using a drill press, cutting them by hand with a mallet and chisel, using a router and more. In this video we will be using the router and manufacturing a simple attachment that is easy to use, and not complicated to set up, to make mortise cuts for mortise and tenon joints.
Watch this and other similar videos on YouTube - https://youtu.be/G9rNbWB1jmc
To make the morise jig, I started off with a pices of 1/4" hardboard. I find this is better that plywood for this knid of a build because the hardboard is is harder than plywood and because you will likely have to drill counter sunk holes into the base, you will want something stronger than plywood to take that force.
Page 62 of 103